Skip to main content

Site Navigation

Your Account

Choose Language

Introduction

To feel the world, feel the creatures,feel internal .CN:为了更好的了解世界,了解他人,了解自己。“见天地,见众生,见自己”

  1. Electronics Assembly  You will need: CN: 电路组装
    • Electronics Assembly You will need: CN: 电路组装

    • The SatNOGS v2 Mechanical Ground Station Assembly. CN: SatNOGS v2 的地面基站机械部分组装

    • TP-Link WR703N

    • SatNOGS PCB. CN: 印刷电路板部分,下同

    • SatNOGS PSU PCB

    • A 4 port USB hub. CN:4端口的USB hub

    • 2 USB micro cables. CN: 2条USB迷你连接线

    • One double wire for 12V to SatNOGS PCB

  2. Using double sided foam tape, place the TP Link on the side as shown. CN:用发泡双面胶把TP Link路由器粘贴在一侧 Place SatNOGS PCB as shown (with foam tape).CN:把发泡双面胶带及PCB板放在图示位置 Place SatNOGS PSU PCB as shown (with foam tape).CN:同上
    • Using double sided foam tape, place the TP Link on the side as shown. CN:用发泡双面胶把TP Link路由器粘贴在一侧

    • Place SatNOGS PCB as shown (with foam tape).CN:把发泡双面胶带及PCB板放在图示位置

    • Place SatNOGS PSU PCB as shown (with foam tape).CN:同上

    • Stick with foam tape and connect the USB hub as shown.CN:按图示粘贴及连接USB hub

  3. Wires are next: Connect 12V from PSU PCB to PCB using two wires as shown.CN:把两块PCB板的12V电源线(红色)和地线(黑色)接好
    • Wires are next:

    • Connect 12V from PSU PCB to PCB using two wires as shown.CN:把两块PCB板的12V电源线(红色)和地线(黑色)接好

    • Connect Stepper motor wires as shown.CN:把步进电机的导线如图示接好

    • Refer to Stepper motor documentation for specifics on colors of wires.CN:如果花花绿绿的线分不清请看详细文档——步进电机部分

  4. You will need 2 USB micro cables.CN:需要两个迷你USB线
    • You will need 2 USB micro cables.CN:需要两个迷你USB线

    • One USB micro cable should start from the PSU PCB and end to TP-Link (for power supply).CN:其中一条从PSU板子连到TP Link,用于供电

    • The other USB Micro cable should start from the USB Hub and end to the Arduino Micro (for data connection).CN:另外一条从USB hub到迷你Arduino的板子,用于数据传输

    • You have now finished all electronics setup of your Ground Station.CN:现在你已经完成了电路部分的组装

Finish Line

One other person completed this guide.

Pierros Papadeas

Member since: 04/23/2014

905 Reputation

7 Guides authored

2 Comments

Please,

What 3D printer and material are you using to print the parts?

Thanks!

Nereu Camara - Reply

Used Objet to make the gears; other parts made with Dimension

(University of Alabama 3D lab)

AB4EJ -

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 6

Past 30 Days: 38

All Time: 9,239